Vehicles
73 not categorized PORSCHE 930 SEAL SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.95135291900 Known as: gasket set / gasket set comprising: piston boot / gasket set / gasket set with scraper ring $ 30 f >>95kn1 50215 View/Change Diagram
$85.04
Make a selection
$31.48
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$14.93
Make a selection PCG5316010S Don't reinstall weathered and worn rubber seals when replacing your door handles. This is a set of four door seals- two larger main seals and two smaller seal. made of nylonized rubber, these seals will never shrink or split. This set is a necessity when restoring a car and installing new chrome handles. General Fitment914 1970-76
$18.13
Make a selection NLA55100300 U-channel screw set. Eight screws for attaching u-channel under the door seal at threshold. Fits all 356.
From $2.64
Make a selection RS21 Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire’s contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline’s sealed camber plates incorporate fk motorsports spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Comes as a set of two. Why are rennline’s strut mounts the best ? General FitmentBOXSTER 2005-08CAYMAN 2006-08 911 2005-08 911 GT3 2007-11
$603.90
Make a selection RS18 Set of two sealed monoball cartridges - front or rear. Most Porsche owners today, especially those of us who take our cars to the track, have equipped our cars with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely tuned alignment settings, thereby reducing your braking and cornering potential. Monoballs are a downside-free improvement; because they eliminate four important sources of suspension slop without making your car's ride harsher. Your Porsche will handle and brake with greater precision...(choose a part on the right to read more) General FitmentBOXSTER 1997-04BOXSTER 2005-08 CAYMAN 2006-08 911 GT3 2007-11 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$250.00
Make a selection
$120.40
Make a selection 91453100000 The 6 critical seals to keep the water out in one handy kit. when it rains, it pours, and we all know how leaky the 40 year old rubber on your 914 can get. replace the ones that matter most; the windshield frame seal, the vertical rollbar seals, and the targa side seals. General Fitment914 1970-76
$374.62
Make a selection
$109.93
Make a selection 96410490100 Known as: gasket set View/Change Diagram
$130.00
Make a selection 90135199800 Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to "get hot"? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your caliper(s). These factory kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper! View/Change Diagram
From $32.14
Make a selection 99970108450 This small seal will stop the transmission fluid leak. easily replaced by removing the rear 13mm headed set screw in the rear tail cover. please remember that you will have to refill the transmission after removing the inner speedometer drive to replace this seal View/Change Diagram
From $1.00
Make a selection 91135295100 Known as: mounting parts / parts kit comprising: expanding spring retaining pin safety seal / mounting parts 1 set View/Change Diagram
From $52.33
Make a selection 10010303803 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings / case must be modified / machined on non rs models. If you have a European rs model, these would be slip fit. This kit also requires 6 qty. Larger o-rings, part # 96410440180 and 6 qty. Larger base o-rings, part # 99970502341 mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high th...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,784.84
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |